109Physics · Geometrical optics

Snell’s Law and Critical Angle

fx-50FH II · COMP · 217 bytes

Recover one refractive index or angle from Snell’s law, including the critical-angle limit.

  • 217 bytes
  • COMP mode
01

Worked examples

Example 1

Original secondary-school physics practice. An optical position sensor sends a narrow beam from a transparent block of index 1.6 into a coupling liquid of index 1.2. The beam meets the boundary at 30° to the normal. Find the transmitted angle to 0.1°, and state whether it bends towards or away from the normal.

Answer
r≈41.8°. The transmitted angle is 41.8°. It is greater than 30°, so the beam bends away from the normal; the sine remains below 1.
Standard solution (without a calculator)
  1. Use n₁ sin i=n₂ sin r with positive, dimensionless indices and 0°≤i,r≤90°. Measure from the normal, not the surface. This assumes ordinary isotropic transparent media and the same optical frequency.
  2. n₁=1.6; n₂=1.2; i=30°.
  3. n₁ sin i=n₂ sin r ⇒ sin r=(1.6/1.2)sin30°=2/3<1.
  4. r=sin⁻¹(2/3)=41.81031490…°≈41.8°.
  5. 1.6 sin30°=0.8=1.2 sin r; r>i.
  6. The transmitted angle is 41.8°. It is greater than 30°, so the beam bends away from the normal; the sine remains below 1.
Do it on the calculator

Example 2

Original secondary-school physics practice. A refractometer directs a monochromatic beam from air, index 1.00, into an unknown transparent liquid. Its incidence angle is 60° and its refracted angle is 30°, both from the normal. Find the liquid’s index to three significant figures.

Answer
n₂≈1.73. The liquid’s index is 1.73. It is greater than the air index, consistent with bending towards the normal.
Standard solution (without a calculator)
  1. Use n₁ sin i=n₂ sin r with positive, dimensionless indices and 0°≤i,r≤90°. Measure from the normal, not the surface. This assumes ordinary isotropic transparent media and the same optical frequency.
  2. n₁=1.00; i=60°; r=30°.
  3. n₂=n₁ sin i/sin r=sin60°/sin30°=√3.
  4. n₂=1.732050807568…≈1.73.
  5. 1.00 sin60°=√3 sin30°; n₂>n₁; r<i.
  6. The liquid’s index is 1.73. It is greater than the air index, consistent with bending towards the normal.
Do it on the calculator

Example 3

Original secondary-school physics practice. A prototype light guide has core index 1.5 and cladding index 1.2. For a ray arriving at the core–cladding boundary from the core, find the critical angle to 0.1°. Decide whether a ray incident at 55° undergoes total internal reflection.

Answer
i_c≈53.1°. The critical angle is 53.1°. Since 55° exceeds it and the ray travels from higher to lower index, total internal reflection occurs; 90° is the limiting transmitted angle.
Standard solution (without a calculator)
  1. Use n₁ sin i=n₂ sin r with positive, dimensionless indices and 0°≤i,r≤90°. Measure from the normal, not the surface. This assumes ordinary isotropic transparent media and the same optical frequency.
  2. n₁=1.5; n₂=1.2; r=90°.
  3. sin i_c=(n₂/n₁)sin90°=1.2/1.5=0.8.
  4. i_c=sin⁻¹(0.8)=53.13010235…°≈53.1°.
  5. 55°>i_c; 1.5 sin55°/1.2=1.023940055…>1.
  6. The critical angle is 53.1°. Since 55° exceeds it and the ray travels from higher to lower index, total internal reflection occurs; 90° is the limiting transmitted angle.
Do it on the calculator
02

When to use it

Recover one refractive index or angle from Snell’s law, including the critical-angle limit. n₁ sin i=n₂ sin r.

Inputs

  • Leave exactly one field blank: type no number and press EXE. Enter every known value again for a new run.
  • A = incident index n₁; B = transmitted index n₂; C = incidence angle i (°); D = refraction angle r (°)

Outputs

  • All four fields start at −1. Blank EXE retains that marker; known 0° must be entered as 0. A wrong blank count gives −3. Out-of-range known values instead re-prompt all four fields, retaining their values: correct the bad field and use blank EXE to retain the others.
  • A normal result is the one missing value; −1 means no admissible index or refracted angle, and −2 means an index is undetermined when both angles are zero. Total internal reflection requires n₁>n₂ and i>sin⁻¹(n₂/n₁). For the critical angle, leave C blank and enter D=90. Equal indices at 90° do not form an ordinary critical-angle case. Geometry across several interfaces must be handled separately.

Conditions and limits

  • Set COMP, Deg and Norm 1. Create the program in an empty P1 with MODE6111; P1–P4 share 680 bytes.
  • Use n₁ sin i=n₂ sin r with positive, dimensionless indices and 0°≤i,r≤90°. Measure from the normal, not the surface. This assumes ordinary isotropic transparent media and the same optical frequency.
  • Use unrounded data and round only the final physical answer. Near a limiting condition, small input errors can cause large result changes; extreme values can overflow.

Sign in to unlock the full programme

Checking access…

The programme code and appendix unlock together.

Checking access…

Sign in to unlock the full programme

Checking access…

The programme code and appendix unlock together.