Circular Motion: Three Modes
Circular Motion: Three Modes
Use the radial equation for a particle in uniform circular motion. M=1 / 2 / 3, A=m (kg), B=r (m), C=v (m/s) / ω (rad/s) / F_max (N) → 1: a_n (m/s²), F (N); 2: f (Hz), rpm, v (m/s), F (N); 3: v_max (m/s)
- 207 bytes
- COMP mode
Worked examples
Example 1
Given the following data for uniform circular motion, determine the quantities listed below. M=1 / 2 / 3 = 1; A=m (kg) = 2; B=r (m) = 8; C=v (m/s) = 6. Find: 1: a_n (m/s²), F (N).
Answer
Standard solution (without a calculator)
- Apply F=mv²/r and rearrange for the unknown. Use nonnegative speed and SI units.
- a_n=v²/r=6²/8=4.5 m/s²
- F=ma_n=2×4.5=9 N
Example 2
Given the following data for uniform circular motion, determine the quantities listed below. M=1 / 2 / 3 = 2; A=m (kg) = 0.5; B=r (m) = 2; C=ω (rad/s) = 5. Find: 2: f (Hz), rpm, v (m/s), F (N).
Answer
Standard solution (without a calculator)
- Apply F=mv²/r and rearrange for the unknown. Use nonnegative speed and SI units.
- f=ω/(2π)=5/(2π) Hz
- rpm=60f=150/π ≈47.74648293
- v=ωr=5×2=10 m/s
- F=mω²r=0.5×5²×2=25 N
Example 3
Given the following data for uniform circular motion, determine the quantities listed below. M=1 / 2 / 3 = 3; A=m (kg) = 800; B=r (m) = 18; C=F_max (N) = 6400. Find: 3: v_max (m/s).
Answer
Standard solution (without a calculator)
- Apply F=mv²/r and rearrange for the unknown. Use nonnegative speed and SI units.
- v_max=√(F_max r/m)=√(6400×18/800)=12 m/s
When to use it
Use the radial equation for a particle in uniform circular motion. M=1 / 2 / 3, A=m (kg), B=r (m), C=v (m/s) / ω (rad/s) / F_max (N) → 1: a_n (m/s²), F (N); 2: f (Hz), rpm, v (m/s), F (N); 3: v_max (m/s)
Input order
- M=1 / 2 / 3
- A=m (kg)
- B=r (m)
- C=v (m/s) / ω (rad/s) / F_max (N)
- Enter each required value, including 0, then press EXE. A blank entry keeps its preset value.
Output order
- 1: a_n (m/s²), F (N)
- 2: f (Hz), rpm, v (m/s), F (N)
- 3: v_max (m/s)
Conditions and limitations
- m>0; r>0; v≥0; ω≥0; F≥0; SI: kg, m, s, N; ω: rad/s
- Enter each required value, including 0, then press EXE. A blank entry keeps its preset value.
- F is the net radial force, not automatically the tension, friction or weight. Draw the force diagram first. Tangential acceleration is outside this model.
- Finite precision may lose very small values; −4 means a positive result underflowed. Oversized calculations can give Math ERROR.
- The program overwrites its working registers and Ans. Enter the data again for every run.
- M∈{1,2,3}; C≥0; M=1 → C=v (m/s); M=2 → C=ω (rad/s); M=3 → C=F_max (N)
- −1: invalid or missing data; −4: positive result too small.
Checking access…