004Mathematics · Approximation and bounds

Range of a Value Rounded Down

Range of a Value Rounded Down

From a value rounded down to a unit, find the lower and upper bounds of the actual value.

  • 53 bytes
  • COMP mode
01

Worked examples

Example 1

A kitchen scale shows masses only in steps of 5 g and always rounds down to the step below. It shows 1285 g for a bag of rice. Let m g be the actual mass of the rice. Find the range of m.

Answer
1285 ≤ m < 1290
Standard solution (without a calculator)
  1. Rounding down: the scale’s step is u = 5 g, a whole step rather than a decimal place. Rounding down is not rounding to the nearest, so ±u ÷ 2 does not apply.
  2. The full interval: m ≥ 1285, but m cannot reach the next step 1285 + 5 = 1290, or the scale would show 1290 g.
Do it on the calculator

Example 2

A length of x m is rounded down (not rounded) to 2 decimal places, giving 7.32 m. Find the range of x.

Answer
7.32 ≤ x < 7.33
Standard solution (without a calculator)
  1. Rounding down: the unit of the last kept place is u = 0.01; ±u ÷ 2 does not apply.
  2. The full interval: x ≥ 7.32, but x cannot reach 7.32 + 0.01 = 7.33, or it would no longer round down to 7.32.
Do it on the calculator

Example 3

A data logger records the concentration of a chemical in a water sample by rounding it down to 3 significant figures. It records 0.0215 mg/L. Let c mg/L be the actual concentration. Find the range of c.

Answer
0.0215 ≤ c < 0.0216
Standard solution (without a calculator)
  1. Rounding down: the third significant figure, 5, is in the ten-thousandths place, so u = 0.0001.
  2. The full interval: c ≥ 0.0215, but c cannot reach 0.0215 + 0.0001 = 0.0216, or it would no longer round down to 0.0215.
Do it on the calculator
02

When to use it

Some approximation questions round a positive value down instead of rounding it to the nearest unit. If the result is a, the actual value x satisfies a ≤ x < a + u: the range is a whole unit wide, not ±u ÷ 2. 004 shows the two bounds; write them as lower ≤ x < upper.

What it is for

  • A positive value rounded down to a unit u (not ordinary rounding)
  • Rounding down to decimal places or significant figures (turn the last kept place into a unit)
  • Checking the interval options of a multiple-choice question

What you enter

  • A: the value after rounding down
  • B: the full unit u of the last kept place (2 decimal places → 0.01; 1290 to 3 significant figures → 10; 0.0215 to 3 significant figures → 0.0001)
  • Enter both numbers every time; do not rely on a blank EXE keeping last time’s value

What it shows

  • The lower bound A (included)
  • Then the upper bound A + u (not included)
  • −1 means an input failed the check; it is not an answer

Check before use

  • Run in COMP. The example uses P1; any empty program area also works.
  • Only for positive values rounded down — this is not rounding to the nearest unit. Enter the value after rounding down, A, and the full unit u, with u > 0 and A > u ÷ 2.
  • Two decimal places → u = 0.01; 1290 to 3 significant figures → u = 10; 0.0215 to 3 significant figures → u = 0.0001.
  • The screen shows only A and A + u; write A ≤ x < A + u yourself. The program does not check that A is a whole number of units u.
  • A may not exceed 10⁸ times u. Use at most 10 significant digits; very long decimals and extreme sizes are outside the intended range.
  • Read the last result and press AC to leave; EXE runs the program again.

Sign in to unlock the full programme

Checking access…

The programme code and appendix unlock together.

Checking access…

Sign in to unlock the full programme

Checking access…

The programme code and appendix unlock together.